Audiovox PRO9056 Installationshandbuch

128-8857b1 of 241Model PRO9056TWInstallation ManualVehicle Remote Start SystemPATENTED: www.voxxintl.com/company/patentsPRO9056TW New Format Add Timi

128-8857b10 of 2410WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS Part #1122585The auxiliary 4 pin connector provides low current outputs to control variou

128-8857b11 of 24112 Pin Transponder Control Output: (Yellow Connector) Part # 1123292a: When selected for while remote start on, the Black wire will

128-8857b12 of 24123) DBI TACH SETTING:Selecting this setting in the option menu indicates that you have a DBI module and have determined that atach s

128-8857b13 of 2413TESTING YOUR INSTALLATION:WARNING!! The following procedure must be performed after the installation of any Remote Start Device. I

128-8857b14 of 2414To Exit Remote Start Override Mode:1. With the system disarmed, Press and Hold the PBLED on.2. Turn the ignition switch on, off, on

128-8857b15 of 2415CAUTION! REMEMBER TO RECONNECT THE BROWN/BLACK NEUTRAL SAFETY WIRETEMPORARILY DISCONNECTED IN STEP 3MECHANICAL NEUTRAL SAFETY SWIT

128-8857b16 of 2416METHOD 1To connect to the key in sensor as shown in method 1:1. Locate the control wire that connects the drivers door pin switch t

128-8857b17 of 2417METHOD 2:To connect to the key in sensor circuit as shown for method 2:1. Locate the control wire that connects the drivers door pi

128-8857b18 of 2418COMPLETING THE INSTALLATION1. Mount the control module up and behind the dash securing it in place with cable ties or screws. Becer

128-8857b19 of 2419INSTALLATION NOTES

128-8857b2 of 242Before You BeginPROFESSIONAL INSTALLATION ISSTRONGLY RECOMMENDEDRoll down window to avoid locking the keys in the vehicle duringinsta

128-8857b20 of 2420The transmitters are pre-programmed from the factory, If you find you need to program new or additionaltransmitters follow the inst

128-8857b21 of 2421SELECTABLE FEATURESThe selectable features of this unit can be set manually as explained on the previous page, or with the RF featu

128-8857b22 of 2422PROGRAMMING BANK 3 (REMOTE START ):You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made

128-8857b23 of 2423RF Programmable Features Bank 3 Is Remote Start Selectable Features:Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6

128-8857b24 of 2424© 2013 Audiovox Electronics Corp., Hauppauge, NY 11788128-8857bFor technical support go to www.pursuitcarsecurity.com or call 1 800

128-8857b3 of 2436 Pin Power / Start Harness #1123742123456Purple Accessory (+)Blue Ignition 1 (+)Red Battery 2 - 12V (+)Red/White Battery 1 - 12V (+)

128-8857b4 of 2442 Pin Transponder Output Harness Part #112329212Red Battery (+) 100mABlack (-) Output While Running 100mA6 Pin Antenna Harness Part #

128-8857b5 of 245This Remote Start/Alarm System is designed to be used with Automatic Transmission - Fuel InjectionGas or Diesel Vehicles Only!INSTALL

128-8857b6 of 2463 Fused RED WIRE: + 12 Volt Battery 2 SourceLocate the vehicle battery wire(s) at the ignition switch. Verification: These wires wil

128-8857b7 of 247WIRING CONNECTIONS: 12 Pin Accessory Input/Output Harness PART # 11237511 Yellow/Black Wire: + 12 Volt Alarm By - Pass OutputNOTE: Y

128-8857b8 of 248B. Ignition 3 Output:Some newer vehicles use a third ignition wire, which is required to start and keep the vehicle's enginerunn

128-8857b9 of 2498 Brown Wire: Positive Inhibit Input 1Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even