128-78331 of 241SELECTABLE FEATURESThe selectable features can be set manually as explained below, or with the RF feature programmer.To set features u
128-783310 of 2410General Motors VATS By-Pass DiagramLight Blue Wire: Ignition 3 OutputThis wire provides a 300mA ground output that becomes active
128-783311 of 2411Green w/ White trace Wire: Entry Illumination Ground OutputThis wire provides a 30 second ground output (300 mA Max.) whenever the
128-783312 of 2412Orange Wire: Ground When Armed OutputThis wire provides a 300 mA ground output when the alarm circuit is armed to control the start
128-783313 of 2413Black Wire: Chassis Ground SourceConnect the Black wire to a known vehicle ground source or to a solid clean metal part of the chas
128-783314 of 2414Negative Door Switch Wiring DetailDark Blue Wire: Delayed 300mA Pulsed Channel 3 OutputThe Dark Blue wire supplies a 300mA ground
128-783315 of 2415WIRING THE 4 PIN AUXILIARY OUTPUT HARNESSThe auxiliary 4 pin connector provides low current outputs to control various functions in
128-783316 of 24162 Pin Transponder Control Output: (Yellow Connector)This output is intended to allow the control of a transponder bypass interface m
128-783317 of 24173 Wire Positive Switched Door Locks:In this application, the Red wire of the door lock harness provides a + 12 volt pulse during th
128-783318 of 24183 Wire Positive Switched 2 Step Door LocksThe green wire provides a positive pulse during arming, or the pulsed + 12 volt lock outpu
128-783319 of 24193a) Within 10 seconds of turning the ignition switch off, Release and then Push On and release thePushbutton Switch 2 times holding
128-78332 of 242To program these selectable features;Action System ResponseTurn ignition on No responsePress and release the valet switch 3 times 1 Ch
128-783320 of 24202. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coilpack. For 8 cylinder, f
128-783321 of 2421Starter wire be connected to the ignition switch side of the Neutral Start Switch. Consideration for the place-ment of a starter in
128-783322 of 2422KEY IN SENSOR CIRCUITS:If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are twoalt
128-783323 of 2423must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must beconnected to the hood pin swit
128-783324 of 2424© 2006 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-7833
128-78333 of 243To exit program mode, turn ignition off, or press and release valet switch.RF Programmable Features Bank 3 Is Remote Start Selectable
128-78334 of 244This Remote Start/Alarm System is designed to be used with Automatic TransmissionVehicles Only! The unit provides a selectable igniti
128-78335 of 245THE RECEIVER/ANTENNA ASSEMBLY:The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash
128-78336 of 246YELLOW WIRE: Starter OutputCareful consideration for the connection of this wire must be made to prevent the vehicle fromstarting whil
128-78337 of 247NOTE: See programming information concerning this wire to allow output during the "START" mode.VIOLET Wire: Accessory Outpu
128-78338 of 248WIRING CONNECTIONS: Multi Pin Accessory Input/Output HarnessWhite w/ Red Trace Wire: Parking Light Flasher FeedThis wire is the commo
128-78339 of 249Purple Wire: (+) Door Trigger InputIf the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords
Kommentare zu diesen Handbüchern